Tuesday, November 10, 2009
Friday, May 1, 2009
Saturday, April 18, 2009
Friday, April 10, 2009
Wednesday, October 22, 2008
Friday, September 12, 2008
Friday, September 5, 2008
Tone Tips: Speaker Cables -Dave Hunter | 09.04.2008
When I say “real speaker cable,” I mean a two-core cable where each stranded core is of an equal gauge (thickness), and — this is the key — not a guitar cord, which has one insulated stranded “positive” wire in the middle of a braided shield serving as the “ground” connection. This might seem obvious: speaker cable for connecting speakers, guitar cords for plugging in your guitar, but the importance of getting it right stems from more than just the name on the wire. While a genuine speaker cable of good quality delivers the amp’s output equally to the speaker’s positive and negative terminals, the unequal design of a guitar cord — again, one thin insulated signal wire, surrounded by one very wide shield — introduces a lot of unwanted capacitance to the connection, which can create an impedance mismatch between amp and speaker. On top of this, the thin positive wire in a guitar cord is of a much lower gauge than you would normally want to use to make an output connection, especially from a powerful amp. The impedance mismatch will in itself strain your amp’s output tubes and output transformer, and will severely choke and dull down your tone as a result; if that thin “hot” wire inside the guitar cord gets too hot and shorts, you could blow your output transformer entirely, necessitating an expensive repair.
The trouble arises from the fact that, in the form taken by many speaker cables made for use with guitar amps, the two types of connecting cables can often look the same from the outside. Most good, modern speaker cables will have their function printed on the outer sheath somewhere, and some will be noticeably thicker than guitar cords, but if it doesn’t say, or if you just don’t know one way or the other, don’t make any assumptions. What often occurs, too, is that a guitarist buys a used amp-and-cab set that comes with a so-called “speaker cable” that the previous owner has used with it for years, and assumes this must indeed be a speaker cable … whereas the guy had been getting away with a guitar cord all along. He might have had the good fortune to avoid damaging the amp in any severe way, but his tone will have suffered at the very least, and so will yours.
How can you tell the difference, if there aren’t words on the cable to tell you? Unscrew the barrel (shield) of the plug at one end, if you can, and take a look at the connections inside. If it’s a guitar cord, you’ll very clearly see one thin “positive” wire in the center connected to the terminal from the tip of the plug, and a braided outer shield that has been twisted and connected to the ground of the plug. A genuine speaker cable, on the other hand, will have two similar looking insulated wires inside (often the insulation on one is white, the other black, but different colors are frequently used too), both of which come from the center of the cord, rather than one being a braided shield that encloses the other. If you can’t check the cable, and have even the least suspicion at all, don’t use it. Discard it, and get a genuine speaker cable. It isn’t worth taking the chance to save the $10 or $20 a decent piece of wire will cost you.
A lot of players wire up their own speaker cables. It’s easy to do, if you know the basics of soldering and have the tools, and usually saves you some money versus purchasing cables, while also giving you the option of customizing the length to suit your needs. Any good quality hi-fi speaker hook-up wire will do the job, and you can often still buy this by the foot or the yard at good hardware stores, or buy a full spool and have plenty on hand for your future needs. Very short amp-to-speaker connections within smaller combo amps can get away with 18 AWG (American Wire Gauge) wire, but I’d want to use 16 AWG for anything more than a foot or so, or 14 AWG for longer cables of two to four feet or more (this is just leaning toward the cautious—and why not, since you’re making these yourself). It’s also worth leaning toward heavier gauges for more powerful amps, which can heat up thinner wires at high output levels. Along with the cable, you just need a pair of good quality phone plugs, a soldering iron, and a little solder, and hook it all up (many plugs have screw-terminal connections, but I don’t trust them: remove the screws entirely and make a good solder connection to the terminal, so you know it’ll hold). With thicker wire gauges the larger plugs available from some suppliers will make it easier to make good connections, and to fit the screw-on barrel over the cable. Even if you have plenty of wire to use, make your cables only as long as you really need them to be and your amp will thank you for it. And while you’re at it, make a spare and carry it to every gig … so you don’t resort to using a guitar cord again out of desperation when your main cord suddenly goes missing.
However great a guitar you’ve got, however rare and refined your priceless vintage or “boutique” tube amp, and despite the precision high-end guitar cords you might be using in front of it, using a guitar cord to make the connection between amp and speaker will instantly deplete your tone. Get a quality speaker cable, or wire up your own, and you will at least know that all the goodness you’re putting into the front end of your amp is making its way out the back.
Original article can be found at Gibson.com
Wednesday, August 27, 2008
Thursday, August 7, 2008
Buying a new Guitar?
1. Know your product.
Knowing what you are looking for is a big step in the right direction. I've browsed eBay in the past and found fakes. One such fake was supposed to be a vintage Gibson. Upon closer inspection of the pictures it was obvious the guitar was not a Gibson. A while back they were having such a problem with fakes that they posted information on how to spot one one their website. You don't want to pay more for something than what it's worth.
2. Check the neck.
Check the neck for straightness. A little bow in the neck is normal and even recommended for proper setup and playability. The neck should not be over-bowed nor should it be twisted. I saw a guitar in a pawn shop once that almost looked like a screw (exaggeration but it was noticeable). Hopefully some unknowing soul didn't "get screwed".
3. Play with it.
If at all possible play the guitar before you buy it. Of course this is not always possible with online purchases but to be truly satisfied and informed you need to pick up the thing and jam a bit. Doing so will reveal any fret buzzes and other issues. Strum chords and play single notes in different playing styles. Listen to the notes.
4. Action!
Check the action (string height). Really high string height could mean a number of problems including a bent neck or fretboard.
5. The Bridge and the Nut.
Check the bridge for issues such as chips dings etc. Likewise check the nut too. A buzz on an open string could mean string nut slots are too low which could require a new nut. Not really an expensive fix but something to look for.
6. Watch the Cracks!
Check the body and neck for any cracks. Strings put a lot of tension on the guitar so cracks could turn out to be a BIG problem.
These are just a few tips that can help save you time and money. Really good deals are to be had and folks have in fact did just that. Unfortunately some have also found out the hard way that really bad deals are also out there. Hopefully armed with a little information will help save you misery down the road. Good Luck!
Friday, July 11, 2008
Lost Hendrix Album Confirmed
07.10.2008
A long lost album of tracks Stephen Stills recorded with Jimi Hendrix over 30 years ago has surfaced, and is being readied for release, according to a report from MusicRadar.com that cited confirmation of the recordings' existence and their imminent release from John McDermott, a long-time Hendrix historian and archivist.
"Stephen has been working with Experience Hendrix to compile an album's worth of sessions recorded with Jimi Hendrix during 1969 and 1970," McDermott told MusicRadar.com. According to the report, no official information on the recordings has been released yet, though McDermott did say he would be the collection's co-producer.
Stills apparently found the lost Hendrix recordings among a stack of old tapes he recorded in the 1970s, either by himself or with various other musicians. According to a report in the Las Vegas Sun, Graham Nash—Stills' long-time bandmate in Crosby, Stills and Nash—is also involved in the collection's release. It is one of 13 CSN-related projects Nash is currently working on.
"In the '70s, he was a recording fool," Nash told the Sun. "He just found a bloody album he made with Hendrix."
Stills' reaction to finding it? "'Oh yeah, I forgot that,'" Nash said. "I want to listen to every track he ever recorded in case he recorded with Al Jolson."
Apparently, several purported recordings of Stills and Hendrix together have previously appeared on various bootlegs, though the authenticity of those recordings had always been in doubt. Only one song from that period—titled "Old Times, Good Times"—has ever officially been released, appearing on Stills' self-titled album that was released in 1970.
It now appears the imminent release of Stills' recent discovery will settle several long-standing debates regarding the authenticity of those bootlegs. One source with close ties to the project told MusicRadar.com, "We have tapes in our archive—Jimi on guitar and bass—plus Stephen had some from his 1970 solo album that he wanted to finish, fix, and mix. From a musical point of view, it's definitely Stephen with Jimi helping, as opposed to a joint collaboration. But it is still a very nice project."
Stay tuned for more updates.—Gabriel J. Hernandez
Thanks to Gibson.com for this article.
The next Satriani???
by Blake Hannon
Friday, December 14, 2007
The Josh Myers Band’s music is entirely instrumental, with lead guitar-focused blues rock in the vein of a couple of above average Joes... guitar players Joe Bonamassa and Joe Satriani. But Myers says that within those notes, he is saying a lot about his life. The band will have a CD release party for its album “Soul Serenade Sessions” at 7 p.m. Saturday, Dec. 15, at Word of Life Church in St. Joseph. To hear how they sound, go to www.myspace.com/joshmyersband.
Q. How and when did the Josh Myers Band come together?
A. The Josh Myers Band really just started as a project. It was me in my basement with a drum machine writing songs about feelings I had or things I was going through. The band developed into me, my 14-year-old son Corey and a close friend Andy West. Just three guys who love to play music.
Q. Who was the first guitar player you heard that made you want to play the instrument?
A. I started out as a drummer when I was 14. After about three or four years of that, someone introduced me to the music of a guitar player named Nuno Bettencourt from the rock band Extreme. That’s what gave me the bug to play. He was so melodic but still had an edge. I really like all styles of music and feel I can learn from it all.
Q. Who influences you now?
A. Wow, it’s hard to name a few because there are so many. Really right now, I’m into Joe Bonamassa, Joe Satriani, Andy Timmons and Hendrix. Really there are far too many to list. I’m always changing my influences to help get new perspectives on guitar.
Q. You are having your CD release party at Word of Life Church here in St. Joseph. Does the CD have a Christian focus?
A. No. The CD is not Christian-focused. I play at Word of Life on the weekends and it is my home church, I love it there. I don’t like labels (like) Christian verses secular. I think putting a label on music is shallow. Music is deeper than that. Music is universal to me. Our music has no words so how can it be labeled? This music was written about life experiences — what I have been through and where I want to go. I want the music to do the same for the listener. It has feeling of hope. Not all of the songs are happy, but the underlying message I’m trying to convey is: Don’t quit. Tomorrow can be better. There is always a new beginning. It’s a matter of life’s perspective.
Q. Tell me a little bit more about “Soul Serenade Sessions.”
A. This is a soundtrack for life in general. We all have music in our day. It’s all around us. We live in a culture where everything is convenient, processed and plastic. The idea of “Soul Serenade Sessions” is that no one is telling you how to think or what to say. You make the songs a soundtrack for your life and what you’re going through. The songs may have a totally different meaning to each listener.
Q. Do you have any musical projects in the near future?
A. I can say yes! I’m a musician and I am always trying to write music that comes from my heart. The music won’t stop in my life until I’m dead and gone. I’m just trying to be me and be true to what I know. Hopefully after “Soul Serenade Sessions” there will be much more to come.
Q. Do you think the instrumental guitar music you play resonates here in St. Joe and elsewhere?
A. I hope so. It may not be a radio market but there is a definite market for instrumental music worldwide. For example: Joe Satriani releases a CD every couple of years followed by a tour which usually sells out on a lot of dates in major cities all over the world. As I said before, this music has no age preference or religious stamp nor does it target any one audience. These are simply me trying to capture feelings and emotions with music!
By Blake Hannon
St. Joseph News-Press
Visit the Josh Myers Band Offical Website Here
Thursday, July 10, 2008
GuitarCardio.com is a web-based tool for building guitar skills. For more information, check out GuitarCardio.com itself.
Thursday, March 6, 2008
Soloing Tips
Taking the spotlight with an improvised solo isn’t as difficult as it might seem. In fact, with a little bit of knowledge and a bit of “go for it” gusto, soloing can be exhilarating for you and your listeners.
By Dianne Spoto
There’s nothing more exciting for a performer than having that moment in the spotlight to shine. One way performers show their stuff is through improvising and taking solos. Solos allow a musician to have the spotlight all to him or herself, and to compose on the spot and express their own unique musical voice. Improvisation gives players an opportunity to show off instrumental prowess, musical intelligence and spontaneity.
However, for some, soloing on stage makes the thought of a root canal seem like fun. Either way, giving improvisation a go can enhance your confidence and build self-esteem, which translates directly to lots of other areas in your life. How can you go wrong with that? Read on for some hands-on tips and tricks to help you dig into the art of the solo and “let ’er rip!”
Practice Techniques: Tried and true prep exercises for before you hit the stage.
1. Listen
Listen to great solos on record. Crank up the volume on some rip-roaring, live solos from your favorite band. Now listen carefully and ask yourself these questions: What catches your ear with this solo? Is it the speed of the notes? The tone? Perhaps there is an incredible amount of expression or rhythmic complexity that makes the solo engaging. Discover for yourself what makes a solo exciting to you.
2. Transcribe
Take that solo that you dig so much and try to memorize it note for note. You can do this by learning to play or sing along to it by ear. But one way to learn the music on an even deeper level is to transcribe the solo by writing down every note and chord change on notation paper. This way, you will learn melody and chord structure and be able to play your own solos over those very changes in time.
3. Record
While you’re in your room practicing alone, turn on the recorder and let it run while you jam. You may be surprised to hear differences between the actual recording and the way you think you sound as you play. Listen to your solo and ask yourself the questions from step No. 1. You might just be pleasantly surprised with your answers!
4. Write
Here’s a fun way to tackle the art of improv: write down five random notes, any notes, and play them on your instrument. Try playing the five notes in as many different ways as possible. For example, play the notes slowly with a beautiful tone. Play them short, staccato and forte. Play them with various rhythms. Play the five notes in a different order each time. Create a melody and rhythm out of the notes. Think of a specific emotion while you play the notes and try to express that emotion as clearly as you can.
5. Jam
Create an avant garde improvisation group! Gather some friends (they don’t have to be trained musicians) and get together with instruments, or hand percussion instruments, and just jam. Make stuff up as you go along, but do it while listening to each other and try to react to each other’s playing. Take turns accompanying as you all take a turn at soloing. Don’t be afraid to let it sound really abstract or even borderline strange! In fact, try to make it sound as wacky as possible. This will open up your mind to allow fun and free thinking without censorship or self-judgment.
6. Riff
A riff is a catchy, repeated chord or series of chords. Most of our favorite songs are built around riffs. Listen to the repeated guitar or keyboard motifs underneath the verses of your favorite recordings. Try to emulate some of your favorite riffs, and make up your own simple riff on piano, guitar or another stringed instrument. Play it over and over and then allow a note or two to come out of your mouth as you accompany yourself with the riff. Enjoy the notes you are singing. As you vamp on the riff, some variations will most likely emerge as your melody organically forms.
Performance Techniques: Now that you have practiced and brushed up on your improvising skills, turn your focus to the stage!
1. Melody Building
Take a section of the melody of the song in which you’re soloing and add notes to it. Use the melody snippet as a base for your improvised solo.
2. Pitch Switch
If you are looking to add momentum or intensity to a solo, try going higher and higher in pitch.
3. Volume
A lot of times when people solo, they automatically increase the volume with every note they play. There is nothing wrong with this, but for variety and surprising intensity, try playing a solo quietly.
4. Safe Landings
Audiences tend to focus on certain notes in a solo, so try breaking up fast, technical passages with long, sustained notes. It will add flavor to your solo and give the audience something to focus on aurally. Liken this to climbing a hill and stopping on a peak to enjoy the view.
5. Know Your Chords
Playing by ear is a gift, but playing by ear to chords that you are knowledgeable of is a skill. Learn the chord structure of everything you solo over and be aware of the notes that make up each chord. That way you can intentionally pull notes out of the chords to put in your solo and avoid “clinkers.”
Coda
At the end of the day, improvising and soloing aren’t about being “right” or “wrong,” or “good” or “bad,” at music. It’s about expressing who you are as a person and musician, and sharing it with others. Though soloing can seem daunting to some, the idea of having a chance to express your particular uniqueness to the world is exciting! Like snowflakes, no two of us are exactly alike; we each have qualities that are completely special and unique. Next time you improvise, think of your musical voice as a snowflake, entirely original and special, like nobody else. Go for it!
In Tune Monthly is the only magazine written exclusively for music making students in grades 7 - 12 and their teachers. Used by teachers as an in-classroom text, the magazine focuses on enriching and broadening the traditional music curriculum in middle and high schools and appeals to the independent player as well.
Friday, February 15, 2008
Warren Haynes Player Tip - Gibson.com
Check out the Video Here
Thursday, January 31, 2008
Studio Tech Tip - Reverb
by Dennis Kambury
Probably one of the first effects known to man, reverb and its distant cousin echo have long added their magic to the sounds we make. Who hasn't enjoyed their vocal prowess in the shower, or shouted "hello" to themselves across a rock or high-rise canyon? For thousands of years, acousticians have sought to enhance our audio endeavors with structures that enhance our music, from the coliseums of ancient Rome to the most modern concert hall, these effects have been natural partners with man and music. But let's face it—not even Bill Gates has room in his house for a coliseum or the Grand Canyon!
As recorded music made its entrance, a new way had to be found to get that ambiance we'd grown to love. Initially, large rooms were built that had the desired reverberant qualities. Engineers would plop a speaker at one end of the room and a mic at the other, playing the sound through the speaker and feeding the output back to the recording console. When a change in the character of the sound was desired, the engineer would move the speaker and/or the mic and try again. For echo, nothing beat the tape machine. By feeding the output of one machine into the input of another and monitoring the playback, echo was created. By feeding some of the echo signal back into the first deck, the echo would be regenerated.
The advent of digital technology has profoundly affected our relationship with reverb and echo, allowing us to recreate traditional reverb, or build imaginary spaces that will never exist in the real world! The latest developments—modeling reverbs—sample real acoustic spaces and use the results to re-create anything from the inside of a Yugo to the Taj Mahal! No longer tied to large spaces or cheesy toilet reverb tanks, digital technology has allowed the hobbyist and project studio owner to add a professional sheen to the mix previously unavailable at any price. In fact, with a healthy enough budget, the project studio owner can use the exact same reverb as a multi-million-dollar recording complex!
The question is, how do you get the best results from your gear? Here are a few tips to help you on your quest to audio nirvana:
1) RTFM (Read That Fine Manual)! Most reverb processors are very programmable. They've generally got a lot of presets, but if you spend the time to learn the ins and outs of your gear, you'll really be able to make it sing in harmony with your music.
2) Avoid too much reverb. You can muddy up a mix easily with too much 'verb. It's better to have too little than too much. If you want a really "wet" sound, but you find the result has entered the mud zone, try increasing the pre-delay (the first echoes that return from a surface, before the diffuse reverberation sound builds up). This will allow the original sound to be clear, but still gives you the wetness you desire.
3) Time your echo to the music. By adjusting the delay time of the echo, you can enhance the pulse of the song. Start with one beat per quarter-note, and speed up or slow down to taste!
4) Use the distance cues inherent in reverb and echo to place your instruments forward or backward in the mix. An extreme example would be a piano mixed low with lots of reverb and echo, combined with a loud, breathy vocal part that is completely dry. It'll sound like the piano is in another room (or possibly another planet, depending on your reverb setting) and the vocalist is right in your ear.
5) There is no right or wrong in audio. Learn this rule well—it's really the only one that counts!
Which reverb/echo is right for you? There's no one answer—you may want hardware or software; painless presets or deep programmability. It will require a bit of research on your part. Given that, I've got a few recommendations that will help you narrow your choices down to a select few. Keep in mind, opinions about reverb are like opinions about guitars—completely subjective!
Dominating the hardware reverb list are units by Lexicon and TC Electronic. These are both fine examples of digital reverb, with useful differences. Here at Musician's Friend, the top ends of these lines are represented by the PCM91 (Lexicon) and the M3000 (TC Electronic). Both 'verbs find homes in some of the world's finest professional studios, as well as some of the world's funkiest project studios. Either one will do your studio proud! Both Lexicon and TC Electronic have several multi-effects units that include their signature reverb sounds plus a host of other effects.
In the mid-priced zone, check out the Yamaha REV500 or REV100. Yamaha was the first company out of the gate with affordable digital reverb—the SPX90—and they continue their legacy of fine gear at affordable prices.
For a slightly different take on reverb, take a look at the Accutronics Accuverb, a high-quality six-spring reverb. That's right—pure, natural, metal springs, just like your guitar amp!
For the budget-minded, you can't go wrong with the Digitech S100. It's a multi-effects processor, including reverb and delay, and weighs in at well under $200.00!
Wondering about software reverbs? We'll cover that in a future installment of Reverb Tech Tips, so stay tuned! In the meantime, dig into your current reverb, and learn it inside and out. You'll never regret it!
Back to Tech Tip-Of-The-Week Archives
This article was taken from Musician's Friend Tech Tips:
http://www.musiciansfriend.com/document?doc_id=88997&src=3NL8AV
Monday, January 28, 2008
Guitarist Humor
1. I am not too loud
2. I already turned it down
Q: What's the difference between a fiddle and a violin?
A: Who cares - neither one's a guitar.
Q: How do you get a guitar player to turn down?
A: Put sheet music in front of him.
Q: How many lead guitarists does it take to screw in a light bulb?
A: 6 - 1 to put the bulb in, and 5 to say, "I could have done that".
"Mommy! Mommy! I want to be a guitarist when I grow up!"
"Now Johnny, you know you can't do both."
Q: How many guitar players do you need to replace a flourescent light?
A: Five. One to actually do it, and four to reminisce about how much better the old tubes were.
Q: What's the difference between a guitar player and a bag of garbage?
A: The garbage gets taken out at least once a week.
Q: What's the difference between a lead guitarist and a terrorist?
A: You can negotiate with a terrorist.